HANNA PHOTOMETER REAGENTS · HI93753
A matched chloride refill for blank-and-sample testing.
Restock the two-liquid chemistry for your HI97753 chloride photometer. Choose 100 or 300 determinations while keeping the same low-level chloride method, reporting units and two-cuvette workflow.
Official Hanna 100-test chloride-set reference photo. Printed lot and expiration dates are illustrative, not the expiration date of supplied stock.
Match the method, not just the element name
HI97753: 0.0 to 20.0 mg/L as Cl⁻. The Mercury(II) Thiocyanate method develops an orange tint and measures chloride ions over 0.0 to 20.0 mg/L as Cl⁻ on the HI97753. Chloride is not free or total chlorine: these reagents do not measure disinfectant residual and are not HI753-25 Checker reagents.
What the selected pack supplies
A complete A/B chloride reagent set for the selected test count. Each determination reacts both a deionized-water blank and a sample, so it consumes 1 mL of A and 1 mL of B in total.
Where this method fits
Designed for low-level chloride checks in water samples within the specified range. For low chloride ion concentrations, rinse the sample cuvette several times with sample first; the manual recommends graduated pipettes for accurately delivering both 10 mL portions. This is not an unrestricted seawater or concentrated-brine claim.
The HI97753 workflow at a glance
Prepare one cuvette with exactly 10 mL of deionized water and a second with exactly 10 mL of sample. Add 0.5 mL of HI93753A-0 to each, stopper and cap, then invert each for about 30 seconds. With a second syringe, add 0.5 mL of HI93753B-0 to each and invert again for about 30 seconds. Insert the reacted deionized-water blank with its cap notch aligned and press Zero for the 2-minute countdown. Once zeroed, replace it with the reacted sample cuvette in the same alignment and press Read.
Check the sample matrix
Intensely colored samples need adequate treatment. Remove large amounts of suspended matter by prior filtration. Neutralize alkaline samples before adding reagents; the sample pH after reagent addition should be about 2.
Choose a pack around your workload
HI93753-01 supplies 100 tests; HI93753-03 supplies 300 tests. The larger pack supplies three times the determinations, not a different measuring range. One order quantity means one complete selected pack. Choose by testing frequency and the lot/expiry markings on supplied stock.
What to have beside the reagent set
Supply the compatible photometer, cuvettes with stoppers and caps, and the measuring/dispensing accessories required by the method separately. Deionized water is also required for the chloride blank. CAL Check standards are separate instrument-verification materials, not replacements for sample reagents.
Handling before you begin
Reagent A is toxic if swallowed and harmful in contact with skin; reagent B causes severe skin burns and eye damage and may corrode metals. Read both US SDS, use the specified protection and arrange appropriate hazardous-waste disposal. Hanna identifies both pack sizes as Dangerous Goods for ground shipment only.
Use the exact-model Method Manual below for the complete procedure, cuvette preparation and temperature guidance. Other documented instruments: HI83300, HI83399. Use the matching method in the manual for your exact instrument.
Frequently Asked Questions
Should I choose 100 or 300 tests?
HI93753-01 supplies 100 tests; HI93753-03 supplies 300 tests. Both are complete reagent sets for the same method. Choose by expected workload and marked expiry dates, not by a different analytical range.
Is chloride the same test as chlorine residual?
No. This method reports chloride ions as Cl⁻, not free or total chlorine disinfectant residual. It is also not the HI753-25 Chloride Checker reagent pack.
Why do I need two cuvettes and deionized water?
The HI97753 zeros a reacted deionized-water blank separately from the reacted sample. Use 10 mL in each cuvette and add both reagents to both. Zeroing untreated sample is not the documented procedure.
How much reagent is consumed per reported chloride test?
Add 0.5 mL of A to each cuvette and then 0.5 mL of B to each. Together, the blank and sample use 1 mL of A and 1 mL of B per determination. Pack test counts refer to this complete workflow.
Where does the two-minute wait belong?
After the additions and mixing, place the reacted deionized-water blank in the HI97753 and use its 2-minute Zero countdown. Then replace it with the reacted sample cuvette and press Read. Follow the manual for cuvette preparation and timing.
Which photometers are documented for HI93753?
Both packs are documented for HI83300, HI83399, HI97753. The procedure and range on this page use HI97753 as the primary reference; follow the exact instrument method when using another model.
Which sample conditions should I check first?
Intensely colored samples need adequate treatment. Remove large amounts of suspended matter by prior filtration. Neutralize alkaline samples before adding reagents; the sample pH after reagent addition should be about 2.
Are the instrument, cuvettes and CAL Check standards included?
No. These are reagent-only packs. Provide the photometer, cuvettes with stoppers and caps, and the method-required sampling and dispensing accessories separately. CAL Check standards are separate instrument-validation materials, not test reagents.